The easiest way is to open up /Settings/default.ini (or your ini, if you've created your own), and paste in the following bits, replacing the existing sections: Īt this point, you should be able to use head movement with your clip/cap point model. You will most likely also want to change the settings for the filter, Accela Mk2 by default. Once the numbers stabilize, you're good to go. Basically, you press calibrate and move your head in yaw, pitch and roll - avoid moving in any translation axis (forward/back, left/right, up/down). This tells PointTracker how far offset the light points are from the center of rotation for your head. One last thing in the PointTracker configuration is the calibration. Roll will most likely be zero or 90, depending how you have the camera mounted. If you have PT 1.1, you also have camera yaw, which is negative if positioned to the left of your screen and positive if to the right. First and foremost, change the 'Tracker Source' to PointTracker 1.0 (1.1 available here with more advanced camera positioning options), click the Settings button under the source, and input the camera settings and measurements of your model.Ĭamera pitch is positive if the camera is pointing up to your face from below your monitor, negative if mounted above. If you're using a head cap/clip, you will want to change a few things. Just make sure your room is well lit, and you should see the video pane in the upper left show your face and the tracking trace. If you're just experimenting with head tracking before buying anything else and you already have a webcam, start up FTNoIR and press the 'start' button - the default settings are totally fine for face tracking. Despite what has been bandied about, in my testing no changes were required to the defaults of the FreeTrack 2.0 protocol (Dummy TrackIR.exe checked, Enable Both interfaces). This adds the necessary ID codes for Star Citizen. #Facetracknoir kostenlose vollversion download#After you've installed this, to get FTNoIR working, you need to also download the FaceTrackNoIR Supported Games.csv file from SourceForge and put it in /Settings, replacing the one that is there. #Facetracknoir kostenlose vollversion full#You want to start with the Full Installer v170 and the Hotfix1 v170 from the FTNoIR Downloads page. The SFH485P LEDs are widely available at all of the online electronics sites (Digikey, Mouser, etc), and everything else can be sourced at the local Radio Shack. The simplest and most straightforward way is outlined over at the FreeTrack forums, here. Once you have the physical frame constructed, it is time for the LEDs. If you have a CNC router/mill, there are some DXFs available here. If you have access to a 3D printer, there are a fair number of clip options around. I'm personally partial to the clip, because it can be cut quickly and easily out of stuff you have laying around the house - cardboard, plastic plates, plastic sheet from the local hardware store, etc. The numbers can be anything, but the defaults listed work very well if you make your model based on those. The PointTracker settings page gives a pretty straightforward view of the geometry of both clip and cap models, as well as what measurements are important. This is the part that always seems to throw people off building their own, but is really simple. Mine are set to this for use with the RGB filter and IR LEDs. For the PS3Eye, the controls are in the CL-Eye Test application, Options Menu, Video Capture Filter. With any webcam, you will probably need to adjust the gain/exposure/color balance to try to best show your face or the light points. Easy, cheap and lets me remove or replace the filters with no fuss. I use a simple piece of 1" PVC with a few cuts from a hacksaw to hold the filter in place. This is enough to let me use my IR model with a sunny window directly behind me, without any modification of the webcam. People have reported using floppy disks and exposed film negative, but I just snagged some lighting gels and stacked red, green, and blue. If you're using an IR point model and not a visible light or your face, you'll probably also want a filter to reduce visible light and let IR light through. #Facetracknoir kostenlose vollversion driver#$1.99 from Code Laboratories for their CL-Eye Driver is not particularly awful, however. #Facetracknoir kostenlose vollversion drivers#The cheapest, fastest webcam is a PS3Eye, but the third party Windows drivers are no longer free from legitimate sources. Most webcams will work, though higher FPS webcams are way, way better. Visible Light Filter (Cut out and stack Red, Green, Blue) FaceTrackNoIR v170 + Hotfix1 v170 + updated 'FaceTrackNoIR Supported Games.csv'
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |